The left front burner clicked on and on without catching. He lifted the cap, showed me it had been seated a half turn off after a cleaning, dried the spark electrode and reset it. First click every time now.
Marisol H.2026-07-28
Coverage
Coverage by county
Clay County is the home territory. Build era, kitchen layout and drive time differ from one community to the next, and so does the failure mix, so coverage is written area by area rather than as one blanket claim.
-
Clay County coverage
Orange Park, Oakleaf Plantation, Eagle Harbor, Pace Island, Fleming Island and the Doctors Lake frontage. One base, one manufacturer, and the failure mix this county actually produces.
-
Oakleaf Plantation coverage
Roughly 6,400 acres straddling the Clay and Duval line, built in phases, with kitchens that reach the same milestones at the same time.
-
Eagle Harbor and Fleming Island
A golf and lake community whose kitchens were designed around built-in appliances from the start, and are now on their second generation of them.
-
Pace Island coverage
A gated Orange Park community whose kitchens were designed around built-in appliances two generations ago. The openings and the circuits are the local constraint.
-
Doctors Lake frontage
Waterfront lots run their own microclimate. Outdoor kitchens here fail from trapped condensate, long supply runs and storm-damaged electronics.
-
Argyle Forest corridor
A Jacksonville address on the Clay County doorstep. Kitchens here were built to a small set of plans, which changes how quickly a fault can be found.
Drive times are typical, not promises — scheduled appointments only. no after-hours or emergency service. Every area gets the same flat $80 diagnostic, the same written estimate before any part is ordered, and the same genuine OEM parts.
What it costs
Does the price change from one area to the next?
No. One book covers the whole territory. What changes from Oakleaf to Pace Island is which fault turns up — build era and kitchen layout decide that — and not what the fix is worth.
$80 Flat $80 diagnostic covering the visit and the full diagnostic sequence, credited toward the repair once you approve the work.
| Repair | Parts and labor |
|---|---|
| Igniter or spark module replacement | $210–$530 |
| Burner valve or orifice service | $220–$680 |
| Oven thermostat or temperature sensor | $180–$550 |
| Convection fan or motor | $270–$710 |
| Control board or touch panel | $470–$1,100 |
| Door hinge, glass or seal | $180–$710 |
| Diagnostic visit | $80 |
Bands, not quotes. 90 days on labor, 365 days on parts. Genuine OEM parts only.
Questions
What gets asked about booking a visit?
- Which areas do you cover?
- Orange Park and Clay County first, including Oakleaf Plantation, Eagle Harbor, Pace Island, Fleming Island and the Doctors Lake frontage, then roughly 40 miles out from there. Scheduled appointments Monday to Friday 8am to 6pm and Saturday 9am to 4pm. No after-hours or emergency service.
- What should I have ready before the technician arrives?
- The model and serial designation from the rating plate, which is usually behind a door or under a drawer, and a clear account of what the appliance was doing when it stopped. Mid-cycle, at ignition or on power-up narrows the list faster than anything measured later.
- What happens if the part has to be ordered?
- The estimate is written down before anything is ordered, and the return fitting visit is not a second diagnostic. Staying with one manufacturer means the common ignition, sensor and thermal parts are usually already on the van, so an order is the exception rather than the routine.
Customer feedback
Calls answered across the county
4.9
out of 5 across 82 customer reviews of this shop. Each one below is a single call, in the words of the person who paid for it.
Two of the three speeds had gone dead and I assumed a new motor. He measured at the speed control instead, found one winding tap open at the switch, and replaced a part far smaller than a whole blower.
Solveig A.2026-03-05
One zone stopped recognising pans it had accepted for years. He measured the coil and the sensing circuit before touching anything, found a failed detection board on that half, and changed only that part.
Hamish P.2026-08-05